Week March 13-17, 2017 Spring-Break

-

Monday 13, 2017

1. We started collecting information for all the shields used in the board (technical information, libraries and diagrams). We are planning to rebuild the board.


Wednesday March 15, 2017

We start tracing the wiring for every shield (component installed in the board).

-        Using the phyton programs used in each shield.

-        Following the wiring in the board.

-        Using the ohmmeter, to trace the wiring.



Thursday, March 16, 2017

The relation of ports and shield used.

SHIELD (COMPONENT)
PORTS
BLACK BEAGLE BONE BOARD
Real Time Clock
CDN.Learn.Adafruit.com/downloads
/pdf/adding-a-real-time-clock-to-beaglebone-block.pdf
P1-GND
P9 - 1 GROUND
P2-5V
P9 - 5 POWER
P3-SDA
P9 - 20
P4-SCL
P9 - 19
GPS: 1590 R-S -> LS20031-Locosys
 + Sparkfun
UART2
P1-3.3V
P9 - 3 POWER
P2-RX
P9 - 21 ?
P3-TX
P9 - 22 ?
P4-GND
P9 - 1 GROUND
P5-GND

Pressure: Honeywell
SSCDRNT1.6 BAAA3
Analog Connection (ADC)
P2-3.3V
P9-3 POWER
P4-GND
P9-1 GROUND
P3-Vout
P9-39 (connected to a resistor)
Accelerometer: Analog Devices
ADXL335
Analog (ADC)  (missing calibration)
P1-COM
P9 - 1 GROUND
P2-Z
P9 - 40
P3-Y
P9 - 38
P4-X
P9 - 36
P5-VSS   3.3V
P9 - 3 POWER
P6-ST

Microphone- MAX4966-ADAFRUIT
(AT1438)

P1-out
P9 - 33 (ACTUALLY IT IS NOT CONNECTED TO 33 )
P2-GND
P9 - 1 GROUND
P3-VCC   3.3V
P9 - 3 POWER
Speaker

P1
P9 - 1 GROUND
P2
P9 - 14
Temperature Sensor

P1
P9 - 37
P2
P9-1 GROUND
Temperature Sensor - Exterior

P1
P9 - 35
P2
P9-1 GROUND
Magnetometer HMC5883L - SPARKFUN
NO USING
P1-GND

P2-VCC

P3-SDA

P4-SCL







Friday, March 17, 2017

The final distribution of the board. We found a wire misconnected in the board, and connection no longer in used.



P9 - 1 GROUND

P9 - 3 POWER 3.3 VOLTS

P9 - 5 POWER 5 VOLTS

P9 - 14
P2 - SPEAKER PIN (ADC)
P9 - 19
P4-SCL RTC CLOCK (ADC)
P9 - 20
P3-SDA RTC CLOCK (ADC)
P9 - 21 ?
P2-RX GPS (ADC)
P9 - 22 ?
P3-TX GPS (ADC)


P9 - 33 (ACTUALLY IT IS NOT CONNECTED TO 33 )
P1-out
P9 - 35
P1 TEMPERUTE SENSOR
P9 - 36
P4-X  ACCELEROMETER
P9 - 37
P1 TEMPERUTE SENSOR
P9 - 38
P3-Y  ACCELEROMETER
P9 - 39 (connected to a resistor)
P3-Vout
P9 - 40
P2-Z  ACCELEROMETER


Comments

Post a Comment

Popular posts from this blog

Camera Field of View Test

-
Image
Objective: To test which GoPro field of view if most optimal for the side camera to record the tray opening and closing. Gaining footage of the horizon is also a secondary goal. Method: GoPro Hero 3+ Silver, the camera that will be used for the sides, was mounted in its casing and payload box to simulate recording on the day of the flight. A previous model of the petri dish assembly will be positioned at various distances on the side. A ruler was used to measure the distance of the payload from the petri dish assembly to record different distance possibilities. The camera was recorded at 1080p and 60fps.   Camera mounted into the new, lightweight casing.  Using a standard ruler to measure distance. Below is a diagram of all the possible frames of second and fields of view for each resolution within GoPro Hero 3+ Black, the camera that will be used for the top.  It has been determined for the side camera to record at 60fps at 1080p, in which the possible fi
Read more

Camera Test in the Sun

-
Image
Last week we were able to test the GoPro cameras outside to see at what temperature the GoPro cameras fail, especially the top camera that would be directly facing the sun. The high was 83F in the afternoon, with several clouds in the sky. The thermometer cord was attached to the back of the top camera to record its changes in temperature. Attaching a thermometer to back of GoPro Inside Payload (Top camera connected to one power bank, side cameras connected to another) Setting up pole and payload so that the camera can record changes in thermometer. Results: 38900 Lux of Sun on Roof Top Camera (#1, Gopro Hero 3+ Black, 720p at 120fps): 98.2F - Initial Thermometer Reading at 10:35AM 116.8F - Thermometer Reading at 11:57AM 108.7F- Thermometer Reading at 1:16PM 36.5GB of memory used, recorded for 2 hours and 52 min (172 min) Side Camera (#2, GoPro Hero 3+ Silver, 1080p at 60fps): Temperature data not recorded for this ex
Read more

End of Week II of Summer 2 - 7/12/2018

-
End of Week II of Summer 2 - 7/12/2018 Our beloved mentor Professor Griffo will be leaving us for the next two week to take a well-deserved vacation. When professor Griffo returns we will only have about two weeks before we need to be ready to launch. This means that we, as a team, need to come together and work hard to complete as much as possible. Alejandro and Ian sat together with the professor to come up with a to-do list for the following weeks; this includes printing at least one completed petri assembly that has been tested, printing all casings, and generally getting ready for a launch in August. Progress Today, Thursday the 12th, we had to present our progress to the rest of the groups working here during the summer. The presentation went well, but we clocked in 7 minutes and 7 seconds from an allowed 3 - 5 minutes. Below is the presentation, if needed for further reference. https://docs.google.com/presentation/d/1whJQM1j4RCveDmQKPiAkz8o1wdrj7RuAVJhWfwd0pDA/edit?usp
Read more